The firing pulses for the first torque direction can be accessed via connector X21A and those for the second torque direction via connector X22A. An active saving process is indicated by the following actions: If unexpected problems are encountered during this process, check whether the firing pulses at the thyristors are occurring simultaneously. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. Different amounts of data can be saved in the 3 memory areas: Green Continuous light A different device is connected to port x and a physical connection exists. For that reason, the physical speed can only be displayed correctly for one data set CDS. 
| Uploader: | Doshakar |
| Date Added: | 21 June 2012 |
| File Size: | 39.83 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 4614 |
| Price: | Free* [*Free Regsitration Required] |
In all other cases, a separate calculation procedure needs to be carried out this particularly applies when using machines with compensation, as they demonstrate a very low armature inductance level.
If you are not using a sense cable, terminals 54 and 55 must be connected.
These notices shown below are graded according to the degree of danger. The frequency of this additional setpoint is changed in 1 Hz increments winamics 1 to Hz.
The motor coasts down. If a V-circuit for 10 V at rated current is to be connected without any changes, either terminals XB-1 and XB-4 with the difference amplifier at 0.
peaeuffe.tk
This 6byte long device identifier is the MAC address. The data set selection dialog appears whenever a data set parameter is changed in the parameter list.
Type Submin D, 9-pin X, X The maximum possible load for the internal firing pulse drivers open drain is 2. The database version must be compatible with the drive software version refer to parameter r The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have hsd safety alert symbol.
This is the only way that you can reset parameters to their factory settings, for example. This is the reason that the physical speed can only be displayed correctly for one data set Dc. You must gse enter this password when deactivating "Parameters disable". Only field precontrol active; field-current controller disabled vcm Set p to rated excitation current. The cable sets listed below for connecting components printed circuit boards or their parts in the case of other mounting types see Chapter 6 are available on request.
The digital outputs are supplied via terminals X, X, and X The MAC address consists of: Potentially susceptible equipment usually refers to controlgear and sensors, including their evaluation circuit. This is an easy method of creating extended telegram interconnections on the basis of existing telegrams.
User parameter list Parameters can be selected for access using the user parameter list in p It is vital for users of the SINAMICS DCM Control Module to realize that they need to check whether the method used for current measurement is really able to map the desired overcurrents and the expected peak dcj within the tolerance required. If you have to work with electronic modules, please note: Digital inputs Digital outputs continuously short-circuit proof Output delay resistive load Switching frequency For resistive load For inductive load For lamp load Maximum lamp load Max.
The drive cannot be operated if no selection is made. It does not result in the drive being switched off and does not have to be acknowledged. Transfer from non-volatile device memory to Memory card Safely removing a memory card Removing the memory card must be requested using p In this state, the user can accept the gsf set by setting p to 3. The last two bytes address the node; i.
Rockman zero manga download
Accept the additional components by writing the following parameter to the CU Note When powering up on a drive for the first time, the software will, if ddcm, be loaded into the Terminal Module. When the dialog is closed, the LED will go out automatically. Failure to follow these Operating Instructions may result in death, serious physical injury, or extensive material damage.
The input signal is reduced to a tenth of its value 10 V to 1 V at rated DC current. The list of current faults is selected here as an example.
The component can now be tilted towards the front and removed from the mounting rail. The send cycle is the shortest possible update time.
Comments
Post a Comment